Tag: A6M2

The A6M Zero in 1/72: Akagi’s Zeros Prepare for Pearl Harbor – Finished Diorama

At long last, below are photos of the finished diorama depicting the Zeros of the Imperial Japanese Navy’s Akagi aircraft carrier preparing to take off as part of the first wave attack on Pearl Harbor on December 7, 1941. I finished this project back in June 2017 but, as often happens, life got in the way of the hobby and I never posted the finished piece.

Below is a photo of my first attempt at this diorama from 2017, taken by the side of the pool.

For a variety of reasons, I was not satisfied with it:

  • The diorama was too small to take good photos;
  • The Zeros came from different die-cast companies and looked odd as the shades were slightly different and the Akagi’s red recognition bands at the rear of the fuselage were different widths;
  • The tail numbers on three of the Zeros were not decaled and looked shoddy;
  • One Kate — even if that Kate was Fuchida’s famous AI-301 — seemed insufficient for the occasion since there were 27 Kates but only nine Zeros on the Akagi’s deck that day;
  • The flags were significantly underscaled and I had inadvertently switched the ones on the inside for the ones on the outside;
  • The island, which was scratchbuilt, lacked some details, including voice tubes, proper staircases, and, notably, the rolled futons used during the Pearl Harbor attack to guard against shrapnel from the expected counterattack that never came;
  • The 4.5 meter rangefinder on the deck just fore of the island was missing, as were the two antennas fore and aft of the rangefinder;
  • The deck needed more figures to simulate the beehive of activity seen in actual photos; and
  • The diorama needed a more appropriate backdrop.

So I kept at it, as time permitted, slowly correcting all the aforementioned problems. I doubled the length of the deck, used nine identical Witty Zeros all with appropriately decaled tail numbers, included seven Kates, recreated the flags at the right scale and placed them on the proper side, added more details to the island, included the range finder just fore of the island, painted more figures (for a total of 85), and added a backdrop that showed the horizon at sea.

I finally finished the improved diorama this week, just in time to post these photos today, on the anniversary of the attack. Nonetheless, I will continue to detail how I constructed each piece of the diorama in future posts. 

Starboard Shots

View from the Front

Portside Shots

View from the Rear

Overhead Views

Detail Shots

Lagniappe 360 Degree Video of Island

Below is a 360 degree video of the Akagi island without the futons used at Pearl Harbor to protect from shrapnel from the expected American counterattack that never materialized. 

Thank you for your indulgence and I hope you enjoyed the photos and video. As always, comments, questions, corrections, and observations are welcome. 

Once again I want to thank my friend and fellow collector Joe Buccellato, of NY, who painted all the best figures in this diorama. I also want to thank Tim Lau, of Maryland, who created the decals for the Zeros and gave me solid advice when I was stuck, and Chris Pflueger, of California, who gave me some great tips on photographing the diorama. I also want to acknowledge Sidnei Maneta, of Brazil, who took the time to provide great information on the Kate tail numbers, which will be covered in a future post. I’d also like to thank Sasa Drobac of Serbia, who designed the incredibly detailed 3D printed binoculars, searchlights, and rangefinders used on the island. Finally, I want to thank Ara Hagopian, of Massachusetts, whose constant encouragement provided the push I needed to actually turn my ideas into these 1/72 scale scenes.

The A6M Zero in 1/72: Akagi’s Zeros Prepare for Pearl Harbor Diorama, Part 2.4 – The Decaled Zeros

This is Part 2.3 of a series of posts on the construction of a Pearl Harbor diorama. It will depict the Zeros of the Imperial Japanese Navy’s Akagi aircraft carrier preparing to take off during the first wave attack. This post is a follow-up to the previous post and concerns only the pre-built 1/72 scale Zeros to be used in the diorama with renumbered tail markings. To understand the concept of this diorama project, please refer to the previous posts. 

The Actual Akagi Zeros

As previously mentioned, the Akagi contributed nine A6M2 Zeros to the first wave attack. As a refresher, below is a table from a previous post of the Zeros that participated in Akagi’s first wave. Akagi's Zeros JPEG from Excel (2) - CopyThe Prebuilt 1/72 Scale Models

The photo below shows the prebuilt 1/72 scale Akagi Zeros currently available. It is immediately evident that of the nine actual Zeros that participated in Akagi’s first wave, only AI-155 and AI-154 have been produced in diecast. Unfortunately, the Corgi AI-154 is unusable as is, since Corgi used black, rather than red, tail numbers.Zero TailsThe Diorama Zeros

For purposes of the diorama, the goal is to use the five models in the photo above plus four spares — two additional Wittys and two additional FOVs. Only the Dragon AI-155 will be used unmodified; the remaining eight will require new tail numbers as per the chart above. Below is a notional photo of the expected result once the decals are applied. Zeros w New Tails

The Decaled Zeros

I searched extensively for MYK Design’s A-72009 Tora! Tora! Tora! Carrier Akagi 1/72 decal sheet (pictured below), since it includes five of the nine necessary tail numbers: AI-103, AI-107, AI-151, AI-155, and AI-158. (The AI-155 decal is unnecessary as I’ll be using the Dragon model that already carries that tail number.)  Alas, I was unsuccessful as the sheet has been out of print for years.

Ultimately, I had no choice but to make the decals myself. I enlarged the image at left, cleaned it up, enhanced the numbers as much as possible, and then reduced it back to 1/72 scale. I then printed the image on Micro-Mark decal paper.

To my dismay, I found that handling the decal sheet resulted in slight smudging. After rereading the decal paper directions, I reprinted the image and “fixed” it onto the sheet with Winsor & Newton fixative. Failure to apply a coat of fixative to protect the image will result in the image smudging like lead on a pencil drawing when touched.

The photo below shows the decal sheet printed on the Micro-Mark decal paper after the fixative had been applied.With decals in hand, I prepared the three Witty models for application of the decals by removing the tail numbers and yellow stripes as necessary — leaving two stripes for the AI-103; one stripe for the AI-107; and no stripes for the AI-158. See photo below.

There are essentially two ways to remove the tampo markings on diecast models: 1) by scraping them off, preferably with an X-Acto #10 curved blade; or 2) by applying some sort of solvent, such as Testors 1148 thinner or standard acetone for nail polish removal. I found that a combination of the two methods worked best for me. (Note: Do not use enamel thinner on plastic models. It will ruin the plastic finish.) Once the original markings were totally removed, I applied a coat of Pledge (Future) floor finish to ensure that the decals found a glossy base that would prevent silvering. (Pledge’s self-leveling properties are amazing!) After waiting a day for the Pledge to cure, I used Micro Set and Micro Sol solutions to apply the decals.

Micro Set prepares the surface where the decal is to be applied by cutting the oils in the paint, thus allowing the decal to slide on the surface, making it easier to reposition the decal as necessary. Micro Sol softens the decal, allowing it to conform to the surface of the model, which is particularly useful on irregular surfaces such as the panel lines and ridges on the Zero tails. Using these two solutions will help make the decals look “painted-on.” 

After waiting another day for the decals to dry, I again applied a coat of Pledge to completely seal the decals between two layers of Pledge. Of course, the Pledge application resulted in a glossy finish. After waiting yet another day, I sprayed the decals with Testors Dull Cote to give the tails a matte finish that matched the rest of the model. The photo below shows the results after the Dull Cote had dried.

In addition to an unmodified Witty model (AI-155), the photo below shows the three decaled Witty models (AI-103, AI-107, and AI-158), plus one decaled FOV model (AI-151). Note that some paint came off the tail of the FOV when I removed the tampo markings, giving it an unintended — though not totally unwelcome — weathered look. (Yes, I’m accepting that which I cannot change.  🙂  )As previously mentioned, Corgi inexplicably applied black tail numbers to the AI-154 (see inset in the photo below), rather than the well-documented red numbers. I removed the black numbers with Testors thinner and applied a decal with correct red numbers following the process discussed above. Note that the MYK Design A-72009 decal sheet did not include the AI-154 so I made the decals using letters and numbers from different fonts to simulate the MYK Design numbers. The lagniappe photo below shows the result. I made the extra decals standing by the tail in case I botched the first application — a common occurrence, at least for me, when applying decals. To summarize, six models are now ready: the unmodified Dragon AI-155 plus five decaled planes — three Witty models (AI-103, AI-107, and AI-158), one FOV (AI-151), and one Corgi (AI-154). I’ve decided not to decal the last three (AI-152, AI-153, and AI-156) as the FOV model did not respond well to removal of the tampo markings. Instead, I’ll use paper covers using the stencil in the previous post.

I apologize for such a tedious post. I realize that except for diehard readers, discussion of the tail numbers can get repetitive and confusing. Still, I think the photos by themselves tell the story. 

Again, thank you for your indulgence and I hope at least some of you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful to other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for a brief discussion of the Zero pilots who participated in Akagi’s first wave attack in the next post.

The A6M Zero in 1/72: Akagi’s Zeros Prepare for Pearl Harbor Diorama, Part 2.3 – The Diorama Zeros

This is Part 2.2 of a series of posts on the construction of a diorama depicting the Zeros of the Imperial Japanese Navy’s Akagi aircraft carrier preparing to take off as part of the first wave attack on Pearl Harbor. Providing the history of the Zero or its technical details is beyond the scope of this article. This post concerns only the prebuilt 1/72 scale Zeros to be used in the diorama. To understand the concept of this diorama project, please refer to the previous posts. 

The Actual Akagi Zeros

As previously mentioned, the Akagi contributed nine A6M2 Zeros and 27 B5N2 Kates to the first wave attack. As a refresher, below is a table from a previous post of the Zeros that participated in Akagi’s first wave. As is readily apparent, the tail numbers are all in the AI-150’s except for AI-103 and AI-107. Up to this point, I had deliberately avoided discussing the tail numbers as creating the correct numbers will be one of the more difficult parts of this project, as discussed below. Akagi's Zeros JPEG from Excel (2) - CopyThe Prebuilt 1/72 Scale Models

The photo below shows the prebuilt 1/72 scale Akagi Zeros currently available.* It is immediately evident that of the nine actual Zeros that participated in Akagi’s first wave, only AI-155 and AI-154 have been produced in diecast. AI-155 — Shigeru Itaya’s Zero — has been produced by Dragon, Forces of Valor, and Witty. A review of each can be found by clicking on the name of the manufacturer. A short biography of Itaya is also available by clicking on his name. AI-154 has been produced by Corgi. Unfortunately, despite all evidence to the contrary, Corgi inexplicably used black tail numbers rather than red numbers, for which there is abundant proof. AFV Club also produced an Akagi Zero — the AI-101 — that participated in the second wave. For the sake of completeness, it will be used in this project so collectors may compare models from all five manufacturers that have thus far produced an Akagi Zero. Zero TailsThe Diorama Zeros

For purposes of the diorama, the goal is to use the five models in the photo above plus four duplicates. The challenge is to create models with all of Akagi first wave numbers other than AI-155. Even AI-154 will be required as the tail number must be in red. The idea is to scrape off the original painted numbers and replace them with appropriate decals so that they match the table above.Corgi AI-154 As thus far I have been unsuccessful in finding the decals, I made a stencil of the tail to cover the tail numbers in the interim. I then scanned the color of each model and applied it to the tail stencil. Matching base colors proved more difficult than I had anticipated.

For those interested in how the colors of the five manufacturers compare, below is a plate showing a scan of each model’s base color. The color of the Corgi model is actually beige and the inset at left matches the model reasonably well. I’m perplexed, however, by the difference in the color of the Corgi model in the photos and conclude it’s due to the lighting. The FOV and Witty colors look very similar but that’s as close to the models as the scanner could make them. Once I made stencils for all five colors, I covered the tail of each model with a new number.The lagniappe photo below provides a notional idea of the intended result. At this point, the tail numbers appear to be a weak part of the project. That will change, however, once the decals are applied. Zeros w New TailsAgain, thank you for your indulgence and I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful to other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for photos of the models once the decals are applied.

* Witty also produced AI-101 and AI-102 but both were used in the second wave and, except for the tail numbers, are identical to the AI-155. While Atlas/Oxford (same casting) also produced aircraft carrier A6M2 Zeros, they did not make an Akagi Zero. Instead, Atlas produced a model from the Kaga while Oxford produced one from the Ryujo.