The A6M Zero in 1/72: Akagi’s Zeros Prepare for Pearl Harbor Diorama, Part 1 – The Concept

I derive more pleasure from my models when they’re combined with appropriate figures and placed in historically accurate settings — obviously within the limitations posed by 1/72 scale. Thus, I was eager to place the Zeros in my collection in a diorama recreating the scene on the Akagi aircraft carrier as its first wave prepared to take off for the attack on Pearl Harbor. This series of posts concerns the construction of such a diorama.

As mentioned in previous posts, the Akagi was the flagship — and one of six aircraft carriers — of the Imperial Japanese Navy’s Kido Butai — the strike force that carried out the attack on Pearl Harbor. The attack was carried out in two waves, each comprising Mitsubishi A6M Zero fighters, Nakajima B5N Kate torpedo and level bombers, and Aichi D3A Val dive bombers. The Akagi contributed nine Zeros and 27 Kate bombers to that first wave. (Akagi’s Val dive bombers participated in the second wave.)

The superb illustration below depicts the Akagi as it prepared to launch its aircraft at Pearl Harbor. Note the nine Zero fighters amidships, parallel to the island, followed by the 27 Kate bombers aft of the midships elevator reaching all the way back to the stern.Force Flagship Akagi 2 (3)(NB: I found the unsourced illustration above on the internet. While sourced illustrations of the Akagi abound, this particular one actually depicts the formation of the Zeros and Kates of the first wave as they prepared to take off for Pearl Harbor. I would appreciate information on its source, both so I may provide proper attribution to the artist and perhaps acquire the plate at higher resolution. If you know the source, please contact me.)

The Akagi measured 855 feet from bow to stern but its wooden flight deck was 817 feet. The goal is to represent the 140 feet of the flight deck delimited by the yellow rectangle shown in the illustration below (roughly 1/6 of the entire flight deck). Akagi Diagram 5The project will require nine A6M2 Zero fighters plus one B5N2 Kate — the lone representative of the 27 Kates of the Akagi in the first wave. That leading Kate is significant, however, as it belonged to Commander Mitsuo Fuchida, who was in overall command of all aircraft participating in the attack on Pearl Harbor. For those of us who grew up watching Tora! Tora! Tora! each year, who could forget Fuchida barking the codeword three times into his radio to indicate the Japanese had achieved complete surprise? 

The diorama will also require construction of the flight deck, the midships elevator, and the island superstructure. The enormous exhaust funnel on the starboard side, as well as the antiaircraft guns on either side of the carrier, are beyond the scope of this project as they’re located below the flight deck. (Forgive the funky orange outlined text. It was necessary to make the text stand out.)

This series of posts will cover the aircraft, pilots, deck crew, flight deck, and island superstructure. With any luck, the last post will bring all these elements together in a fairly straightforward diorama. Here’s the plan:

Part 1:      The Concept

Part 2.1:   The Actual Zeros
Part 2.2:   The Model Zeros
Part 2.3:   The Diorama Zeros
Part 2.4:   The Decaled Zeros

Part 3.1:   The Actual Pilots
Part 3.2:   Masanobu Ibusuki
Part 3.3:   Japanese Pilots and Crew in 1/72 Scale

Part 4:      The Flight Deck

Part 5:      The Island

Part 6:      The Finished Diorama

The lagniappe photo below of aircraft preparing to take off from the Akagi provides a good idea of the project.Akagi__class_PH2W_fullWhile I intend to complete this project in the next three months, please remember the following stanza from Robert Burns’ immortal Scottish poem Tae a Moose, later popularized in English by John Steinbeck’s novel Of Mice and Men:

“But, Mousie, thou art no thy lane,
In proving foresight may be vain;
The best-laid schemes o’ mice an’ men
Gang aft agley,
An’ lea’e us nought but grief an’ pain,
For promis’d joy!”

Again, thank you for your indulgence and I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful to other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Please do contact me if you know the source of the illustration. Stay tuned for a synopsis of the Akagi’s first wave Zeros in the next post.

 

The A6M Zero in 1/72: Shigeru Itaya Leads the Zeros at Pearl Harbor, Part 4 – The Witty Wings Model

This is Part 4 of Shigeru Itaya Leads the Zeros at Pearl Harbor. It is a review of the Witty Wings 72-012-001 1/72 scale model of Itaya’s Zero at Pearl Harbor. For a brief biographical note on Shigeru Itaya and reviews of the Dragon Wings and Forces of Valor models of the same aircraft, please refer to the previous three posts. Relevant information on Itaya’s aircraft from those posts is repeated below to make this review self-contained. The reader may want to skip directly to the review of the Witty Wings model. 

Itaya’s A6M2 Zero, Tail No. AI-155

As discussed in Part 1, Itaya led the 43 Zeros from all carriers in the first wave of the attack on Pearl Harbor. In each wave the Zero planes were the first airborne, both because they needed the least runway to take off and in order to protect the slower, less maneuverable torpedo and dive bombers that followed. As the leader of the first wave of Zeros, Itaya was the first Japanese pilot airborne during the attack.

As noted previously, there is precious little information available on Itaya. This dearth of information extends to Itaya’s plane at Pearl Harbor, a Mitsubishi A6M2 Zero, tail no. AI-155. Although there are some references on the internet that Itaya’s Zero’s tail no. may have been something other than AI-155, the books I consulted consistently use that number. To my knowledge, there are no existing photos of the AI-155, though there are enough photos of other planes from the Akagi aircraft carrier to give us a reasonably accurate understanding of its colors and markings.

Below is a color profile from what is probably the most comprehensive source of information on the colors and markings of WWII Japanese aircraft, Eduardo Cea’s eight-volume treatise entitled Japanese Military Aircraft. I scanned this particular profile from Volume 2, The Air Force of the Japanese Imperial Navy: Carrier-Based Aircraft, 1922-1945 (I). While I’m aware that there are a number of errors in the English translation of the Spanish text that are somewhat distracting, the series is beautifully illustrated, incredibly informative, and inarguably comprehensive, and, being fluent in Spanish, I blithely overlooked the errors. 🙂 The profile is reproduced here for discussion purposes under the fair use exception to the copyright laws.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroItaya’s Zero at Pearl Harbor has been released in 1/72 scale by three different manufacturers: Dragon Wings 50017; Forces of Valor 85032; and Witty Wings 72-012-001. This post concerns the Witty Wings model. The Dragon Wings and Forces of Valor models were reviewed in the previous two posts. 

The Witty Wings 72-012-001 Zero

Below is a portside view of the Witty model. Unlike the Dragon and FOV models, which are caramel and ivory, respectively, the Witty model is a pale gray that tends towards white. The photos below are equivalent to those of the Dragon and FOV model. I took them photos at the same time, alternating the model for each different shot, so as to control for lighting and angle. As is clear from the photos, the pale color of the Witty model does not photograph well or, more accurately, I lacked the skills to photograph the Witty model well.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroNote that the panel lines are faintly visible. The diminutive width of the lines is a feature of the Witty that pleased many collectors, as they appear to be more to scale than those of other manufacturers. In addition, unlike Dragon, Witty did not apply any type of wash to highlight the lines, making them appear even fainter. It is this combination of smaller size and lack of a wash that gives the impression that the panel lines are close to scale. While I understand the desire for accuracy in scale and respect the point of view, I find the Witty lines too faint. The Dragon panel lines may be too pronounced; the Witty lines, however, are not pronounced enough. Still, I suspect a very light inking of the Witty lines would result in Goldilocks panel lines.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroThe photo below provides an excellent view of the tail number “AI-155.” As mentioned in the Dragon and FOV reviews, the “AI” code was the designation for the Akagi aircraft carrier. In the three-digit number after “AI”, the first digit (“1”) indicates that it is a fighter plane. The last two digits (“55”) are simply the aircraft number within the unit. The tail numbers on Japanese carrier aircraft were usually red.

Note also the three horizontal yellow stripes on the tail that indicated command: three stripes for the group leader; two stripes for a squadron leader (9 aircraft); and one stripe for a flight leader (3 aircraft). Note also the “no step” rectangular area outlined in red at the rear of each wing next to the wing root.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroThe photo below provides an excellent view of the Hinomaru, which was carried on both sides of the fuselage aft of the wing and on both the upper surface and underside of each wing — six “circles of the sun” in total. The vertical red stripe on the fuselage is the identification mark for the aircraft carrier Akagi.

Note also the manufacturing plate stenciled just aft of the red stripe. The inset shows that the plate bears the number 1575, meaning it was the 1,575th Zero built. The “2-2-9” means it was built in the Japanese year 2602, second month, ninth day = February 9, 1942. (Yes, two months after Pearl Harbor. 🙂 Like FOV, Witty “borrowed” this particular stencil from a Zero recovered at Port Moresby in April 1942.) Incidentally, the A6M is called the “Zero” because it first entered service in the Japanese year 2600 (1940), the zero year of the new Japanese century. Please bear in mind that the entire plate is just 4mm wide (just over 1/8 inch). Though the manufacturing plate on the Witty is not as crisp as those on the Dragon and FOV models, Witty should still be commended for the effort.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroBelow is a shot of the starboard side. Note the absence of the manufacturing plate, which was only stenciled on the port side.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroIn the photo below, note the polished natural metal propeller. Note also the two red warning stripes on the tips of the blades that created two neat red circles when the propeller was spinning. As is the case with the vast majority of 1/72 scale prebuilt models, the propeller spins freely.

Note the outlets for the 20mm cannons on the leading edges of the wings just above the landing struts. Also on the leading edge of the portside wing, note the pitot tube (shadow on floor), which cannot be taken for granted. The Corgi Zeros, for example, do not have one.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, ZeroAs with the Dragon and FOV models, the photo below shows that the landing strut covers on the Witty also have the “55” that matches the last two digits of the tail number. Note that unlike Dragon and FOV, Witty omitted the oval-shaped fasteners on the cowling. Note also the metal drop tank that gave the Zero an extra 73 imperial gallons of fuel (87 US gallons), significantly increasing its range. Later drop tanks were made of wood and had a slightly different shape. Note also that, like FOV, Witty included a pilot.1/72, 72-012-001, A6M, AI-155, Akagi, IJN, Itaya, Japanese Navy, Pearl Harbor, Witty, Zeke, Zero

The Rub 

Well, no, not really a rub — more of a quibble. As previously mentioned, Witty inexplicably omitted the oval-shaped fasteners on the cowling, resulting in a generic-looking cowling. I initially assumed that Witty intentionally omitted the fasteners in order to use the same cowling on its three different Zero models (A6M2, A6M3, and A6M5). However, upon taking a closer look, I realized that the cowling was indeed that for an A6M2 — sans fasteners.

The photo triptych below of three different Witty Zero models demonstrates that Witty crafted a different cowling for each of their three models. The cowling on the A6M2 is wider and shorter than that on the A6M3, reflecting the different engines used on each, and has a scoop that runs the length of the cowling. The A6M2 cowling also lacks the individual exhaust pipes that protrude from the cowling flaps on the A6M5. Zero Triptych

The lagniappe photo below shows that while Witty neglected the fasteners, it offset the lapse somewhat by including the aircraft number “55” on the underside of the cowling as was done on the strut covers — a trivial detail perhaps, but pleasing nonetheless. While other manufacturers included the number on the landing strut covers, Witty alone included the number on the cowling.034 (3)

The Upshot

The Witty 72-012-001 Mitsubishi A6M2 Zero is a beautiful model that closely resembles the original. The excellent casting shows no perceptible problems in its proportions. The panel lines, though faint, are the closest to scale. The cowling, propeller, and undercarriage are all well executed, with no apparent issues other than the missing cowling fasteners. The markings are accurate and crisp and the aircraft number on the underside of the cowling is a neat detail. All Witty Zeros come in wheels down version only, which, although not ideal, still gives the collector the option to display the models on their stands or use them without the stands in dioramas. Matchbox, for example, made its Zeros in wheels up mode only, making it nearly impossible to use in dioramas. While Witty included no features such as a sliding canopy like Dragon or a removable cowling like FOV, their absence does not detract from the model. In short, the Witty A6M2 Zero is a terrific little model — a proud replica of the real thing — and even a cursory review of model aircraft forums reveals that it is a favorite among Zero collectors.

Again, thank you for your indulgence and I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for a simple diorama of Itaya’s aircraft preparing to take off from the Akagi aircraft carrier at Pearl Harbor in the next post.

The A6M Zero in 1/72: Shigeru Itaya Leads the Zeros at Pearl Harbor, Part 3 – The Forces of Valor Model

This is Part 3 of Shigeru Itaya Leads the Zeros at Pearl Harbor. It is a review of the Forces of Valor 85032 1/72 scale model of Itaya’s Zero at Pearl Harbor. For a brief biographical note on Shigeru Itaya and a review of the Dragon Wings model of the same aircraft, please refer to the previous two posts. Relevant information on Itaya’s aircraft from those posts is repeated below to make this review self-contained. The reader may want to skip directly to the review of the FOV model. 

Itaya’s A6M2 Zero, Tail No. AI-155

As discussed in Part 1, Itaya led the 43 Zeros from all carriers in the first wave of the attack on Pearl Harbor. In each wave the Zero planes were the first airborne, both because they needed the least runway to take off and in order to protect the slower, less maneuverable torpedo and dive bombers that followed. As the leader of the first wave of Zeros, Itaya was the first Japanese pilot airborne during the attack.

As noted previously, there is precious little information available on Itaya. This dearth of information extends to Itaya’s plane at Pearl Harbor, a Mitsubishi A6M2 Zero, tail no. AI-155. Although there are some references on the internet that Itaya’s Zero’s tail no. may have been something other than AI-155, the books I consulted consistently use that number. To my knowledge, there are no existing photos of the AI-155, though there are enough photos of other planes from the Akagi aircraft carrier to give us a reasonably accurate understanding of its colors and markings.

Below is a color profile from what is probably the most comprehensive source of information on the colors and markings of WWII Japanese aircraft, Eduardo Cea’s eight-volume treatise entitled Japanese Military Aircraft. I scanned this particular profile from Volume 2, The Air Force of the Japanese Imperial Navy: Carrier-Based Aircraft, 1922-1945 (I). While I’m aware that there are a number of errors in the English translation of the Spanish text that are somewhat distracting, the series is beautifully illustrated, incredibly informative, and inarguably comprehensive, and, being fluent in Spanish, I blithely overlooked the errors. 🙂 The profile is reproduced here for discussion purposes under the fair use exception to the copyright laws.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroItaya’s Zero at Pearl Harbor has been released in 1/72 scale by three different manufacturers: Dragon Wings 50017; Forces of Valor 85032; and Witty Wings 72-012-001. This post concerns the Forces of Valor (FOV) model. The Dragon Wings model was reviewed in the previous post. A review of the Witty Wings model will follow shortly in a separate post, with equivalent photos to the other two for ease of comparison.

The Forces of Valor 85032 Zero

Below is a portside view of the FOV model. Unlike the Dragon model, the FOV model does not have the caramel “ameiro” finish. Its tone is not gray, either; instead, it’s more of a light ivory.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroIn the photo below, note the somewhat deep panel lines throughout the model. Though they are clearly overscaled — about as pronounced as Dragon’s — they do not necessarily detract from the model because, unlike Dragon, FOV did not highlight them with a black wash.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe photo below provides an excellent view of the tail no. “AI-155.” As mentioned in the Dragon review, the “AI” code was the designation for the Akagi aircraft carrier. In the three-digit number after “AI”, the first digit (“1”) indicates that it is a fighter plane. The last two digits (“55”) are simply the aircraft number within the unit. The tail numbers on Japanese carrier aircraft were usually red.

Note also the three horizontal yellow stripes on the tail that indicated command: three stripes for the group leader; two stripes for a squadron leader (9 aircraft); and one stripe for a flight leader (3 aircraft). Note also the “no step” rectangular area outlined in red at the rear of each wing next to the wing root.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe photo below provides an excellent view of the Hinomaru, which was carried on both sides of the fuselage aft of the wing and on both the upper surface and underside of each wing — six “circles of the sun” in total. The vertical red stripe is the identification mark for the aircraft carrier Akagi.

Note also the manufacturing plate stenciled just aft of the red stripe. The inset shows that the plate bears the number 1575, meaning it was the 1,575th Zero built. The “2-2-9” means it was built in the Japanese year 2602, second month, ninth day = February 9, 1942. (Yes, two months after Pearl Harbor. 🙂 Forces of Valor “borrowed” this particular stencil from a Zero recovered at Port Moresby in April 1942.) Incidentally, the A6M is called the “Zero” because it first entered service in the Japanese year 2600 (1940), the zero year of the new Japanese century. Please bear in mind that the entire plate is just 4mm wide (just over 1/8 inch). Though the manufacturing plate is not as crisp as Dragon’s, FOV should still be commended for the effort.dragon-zero-port-w-inset-2Below is a shot of the starboard side. Note the absence of the manufacturing plate, which was only stenciled on the port side.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroIn the photo below, note that FOV incorrectly painted the propeller white. The propeller should have been polished natural metal, like the Dragon’s. Note also the two red warning stripes on the tips of the blades that created two neat red circles when the propeller was spinning. As is the case with the vast majority of 1/72 scale prebuilt models, the propeller spins freely.

Note the outlets for the 20mm cannons on the leading edges of the wings just above the landing struts. Also on the leading edge of the portside wing, note the pitot tube, which cannot be taken for granted. The Corgi Zeros, for example, do not have one.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe photo below shows that the landing strut covers on the FOV model, like the Dragon’s, also have the “55” that matches the last two digits of the tail number. The FOV also has the correct A6M2 cowling, which had four oval-shaped fasteners on each side of the matte black cowling, one on the front part of the cowling and three on the sides. Note also the metal drop tank that gave the Zero an extra 73 imperial gallons of fuel (87 US gallons), significantly increasing its range. Later drop tanks were made of wood and had a slightly different shape.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe Feature

It was a welcome surprise that the cowling on the FOV Zero is a separate, removable piece that reveals a Sakae two-row 14-cylinder radial engine. The basic motor is unlikely to make any collector salivate, as it lacks detail, but it looks the part, particularly without magnification. As I’ve pointed out in the past, special features often come at the expense of accuracy, as with the opening canopy on the Dragon model. However, the removable cowling on the FOV is a simple feature accomplished without loss of accuracy that opens up diorama possibilities. The one quibble would be the white wash to highlight the fasteners, which can be easily remedied with a simple black wash. Note also that, unlike Dragon, FOV included a pilot.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe Rub

Some collectors were critical of the unsightly screw holes on the underside of the wings and fuselage, as can be seen in the lagniappe photo below, used to secure the model to the packaging. While they’re noticeable and unattractive when you flip the model on its back, it is somewhat of a consolation that they’re on the underside of the model and, at least for me, were not a deal-breaker. Still, it may be a consideration for more serious collectors.1/72, 85032, A6M, AI-155, Akagi, FOV, Forces of Valor, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe Upshot

The Forces of Valor 85032 Mitsubishi A6M2 Zero is an attractive model that resembles the original fairly well.  The excellent casting shows no perceptible problems in its proportions. The cowling, propeller, and undercarriage are all well executed, with no apparent accuracy issues. The markings are accurate, though not as crisp as those on the Dragon. The removable cowling is a welcome feature for those who build dioramas. The FOV 85032 Zero, released under the enthusiast series, was also released as a 95032 regular issue. The only difference between the two releases is that the 85032 has both wheels up and wheels down options, while the less expensive 95032 only has a wheels down option. I have both versions and there appears to be no difference in the finish or weathering. In my opinion, the FOV Zero is a great little model that compares favorably with Zero models of most other manufacturers. 

Again, thank you for your indulgence and I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for a review of the Witty Wings model of the very same aircraft in the next post.

The A6M Zero in 1/72: Shigeru Itaya Leads the Zeros at Pearl Harbor, Part 2 – The Dragon Model

This is Part 2 of Shigeru Itaya Leads the Zeros at Pearl Harbor. It is a review of the Dragon Wings 50017 1/72 scale model of Itaya’s Zero at Pearl Harbor. For a brief biographical note on Shigeru Itaya, please refer to the previous post. Today, December 7, 2016, on the 75th anniversary of the attack on Pearl Harbor, let us remember the men who died that day.

Itaya’s A6M2 Zero, Tail No. AI-155

As discussed in Part 1, Itaya led the 43 Zeros from all carriers in the first wave of the attack on Pearl Harbor. In each wave the Zero planes were the first airborne, both because they needed the least runway to take off and in order to protect the slower, less maneuverable torpedo and dive bombers that followed. As the leader of the first wave of Zeros, Itaya was the first Japanese pilot airborne during the attack.

As noted previously, there is precious little information available on Itaya. This dearth of information extends to Itaya’s plane at Pearl Harbor, a Mitsubishi A6M2 Zero, tail no. AI-155. Although there are some references on the internet that Itaya’s Zero’s tail no. may have been something other than AI-155, the books I consulted consistently use that number. To my knowledge, there are no existing photos of the AI-155, though there are enough photos of other planes from the Akagi aircraft carrier to give us a reasonably accurate understanding of its colors and markings.

Below is a color profile from what is probably the most comprehensive source of information on the colors and markings of WWII Japanese aircraft, Eduardo Cea’s eight-volume treatise entitled Japanese Military Aircraft. I scanned this particular profile from Volume 2, The Air Force of the Japanese Imperial Navy: Carrier-Based Aircraft, 1922-1945 (I). While I’m aware that there are a number of errors in the English translation of the Spanish text that are somewhat distracting, the series is beautifully illustrated, incredibly informative, and inarguably comprehensive, and, being fluent in Spanish, I blithely overlooked the errors. 🙂 The profile is reproduced here for discussion purposes under the fair use exception to the copyright laws.1/72, 50017, A6M, AI-155, Akagi, Eduardo Cea, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroItaya’s Zero at Pearl Harbor has been released in 1/72 scale by three different manufacturers: Dragon Wings 50017; Forces of Valor 85032; and Witty Wings 72-012-001. This post concerns the Dragon Wings 50017. Reviews of the other two will follow shortly in separate posts, with equivalent photos of each of the three models for ease of comparison.

The Dragon Wings 50017 Zero

Below is a portside view of the Dragon model. Immediately apparent is the beautiful caramel finish. Putting aside the continuing debate about whether the caramel color was the effect of a protective layer of varnish or the natural result of the aging of the pigments, the fact remains that the Zeros had an “ameiro” tone, which means “caramel-colored” in Japanese. Upon review of Zeros in my collection from a dozen different manufacturers, I’m convinced that Dragon is the only manufacturer that got it right (though Hobby Master produced some terrific “ameiro” D3A1 Vals). If nothing else, the Dragon finish matches the description and color plates in Cea’s eight-volume set on Japanese planes.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroIn the photo below, note the pronounced panel lines, which disappointed some collectors. In my view, however, it is not so much that the lines are significantly overscaled as the fact that Dragon inexplicably “inked” them — for lack of a better term — as one would highlight the crevices on a tank with an umber wash to make them stand out better. It is this combination of overscaling and “inking” that gives the impression that the panel lines are deeper and wider than they actually are.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, Zero

The photo below provides an excellent view of the tail no. “AI-155.” The “AI” code was the designation for the Akagi aircraft carrier. In the three-digit number after “AI”, the first digit (“1”) indicates that it is a fighter plane. The last two digits (“55”) are simply the aircraft number within the unit. The tail numbers on Japanese carrier aircraft were usually red except on two carriers (Zuiho and Hosho) whose tails were already red. The identification numbers on aircraft from those two carriers were white so as to make them stand out against the red tails. 

Note also the three horizontal yellow stripes on the tail that indicated command: three stripes for the group leader; two stripes for a squadron leader (9 aircraft); and one stripe for a flight leader (3 aircraft). Note also the “no step” rectangular area outlined in red at the rear of each wing next to the wing root.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, Zero

The photo below provides an excellent view of the Hinomaru, which was carried on both sides of the fuselage aft of the wing and on both the upper surface and underside of each wing — six “circles of the sun” in total. The vertical red stripe is the identification mark for the aircraft carrier Akagi.

Note also the manufacturing plate stenciled just aft of the red stripe. The inset shows that the plate bears the number 7702, meaning it was the 7,702nd Zero built. The “2-3-30” means it was built in the Japanese year 2602, third month, thirtieth day = March 30, 1942. (Yes, more than three months after Pearl Harbor. 🙂 ) Incidentally, the A6M is called the “Zero” because it first entered service in the Japanese year 2600 (1940), the zero year of the new Japanese century. Please bear in mind that the entire plate is just 4mm wide (just over 1/8 inch). Again, Dragon’s attention to detail is remarkable.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroBelow is a shot of the starboard side. Note the absence of the manufacturing plate, which was only stenciled on the port side.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroIn the photo below, note the polished natural metal propeller with the two red warning stripes on the tips of the blades. As is the case with the vast majority of 1/72 scale prebuilt models, the propeller spins freely. Note the outlets on the leading edges of the wings just above the landing struts for the 20mm cannons. Also on the leading edge of the portside wing, note the pitot tube.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, ZeroThe photo below shows the aircraft’s number “55” on the landing strut cover, which matches the last two digits of the tail number. Note the correct cowling for an A6M2, which had four oval-shaped fasteners on each side of the matte black cowling, one on the front part of the cowling and three on the sides. Note also the metal drop tank that gave the Zero an extra 73 imperial gallons of fuel (87 US gallons), significantly increasing its range. Later drop tanks were made of wood and had a slightly different shape.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, Zero

The Feature and the Rub

In the close-up below, note that the canopy slides back — an interesting feature of the Dragon model. While some collectors were critical of the noticeable gap on the rear bottom part of the canopy necessary to allow the front canopy to slide back, some of us applauded this precise feature as it opens up significant diorama possibilities. Quite obviously, the gap is overscaled. As I’ve pointed out in the past, added features often come at the expense of accuracy. Still, in this particular instance, the gap looks fine when the canopy is open. Please bear in mind that close-up photos greatly amplify defects.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, Zero

The Interior 

The lagniappe close-up photo below provides a good view of the interior of the canopy. Note the superbly detailed instrument panel and the handle of the control column. To my knowledge, Dragon is the only manufacturer that produced a prebuilt model with an opening cockpit and, therefore, with a detailed instrument panel. Unfortunately, Dragon did not include a pilot.1/72, 50017, A6M, AI-155, Akagi, Dragon, IJN, Itaya, Japanese Navy, Pearl Harbor, Zeke, Zero

The Upshot

The Dragon Wings 50017 Mitsubishi A6M2 Zero is a superb model that closely resembles the original. The excellent casting shows no perceptible problems in its proportions. The cowling, propeller, and undercarriage are all well executed, with no apparent accuracy issues. The “ameiro” finish is beautiful, though, admittedly, the “inked” panel lines detract from the overall effect. The markings are accurate and crisp throughout. The sliding canopy is a welcome feature, at least for those of us who build dioramas. All Dragon Zeros came with wheels up and wheels down options and, in addition, this particular Dragon Zero issue included a diorama deck and display case. In my humble opinion, it’s a terrific little model that compares favorably with Zero models of most other manufacturers. 

Again, thank you for your indulgence and I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for a review of the Forces of Valor model of the very same aircraft in the next post.

The A6M Zero in 1/72: Shigeru Itaya Leads the Zeros at Pearl Harbor, Part 1 – The Pilot

I had been contemplating doing a series on the A6M Zero, the Japanese Imperial Navy’s legendary fighter, for quite some time. However, I found the task daunting as there were several different versions of the Zero and, by my count, 15 different manufacturers who have tried their hand at producing prebuilt 1/72 scale models of Japan’s iconic fighter. Together, they have released more than 50 prebuilt Zeros in 1/72 scale. A6M2s, A6M3s, A6M5s, clipped wings, floatplanes, carrier-based, land-based — I was completely at a loss about where to begin. Then I had an epiphany: Start at the Beginning — literally.  🙂

The United States entered WWII following the Japanese attack on Pearl Harbor. That attack occurred in two waves of aircraft taking off from Japanese carriers, each wave comprising Zero fighters, torpedo bombers, and dive bombers. In each wave, the Zeros were the first airborne, both because they needed the least runway to take off and in order to protect the slower, less maneuverable torpedo and dive bombers that followed. The pilot who led the Zeros in the first wave and the first to take off from a Japanese carrier was Shigeru Itaya, flying his A6M2 off the flagship carrier Akagi. Thus, one can reasonably argue that Itaya’s Zero was the first Japanese aircraft to take an aggressive action against the United States, in essence beginning the Pacific War.

Shigeru Itaya

This site is dedicated to 1/72 scale models and presumes general knowledge of WWII on the part of the reader. Thus, I’m ordinarily reticent to regurgitate historical information, as there are plenty of sources on the internet accessible to any reader. If I can readily find information, so can others. 1/72, A6M, AI-155, Akagi, IJN, Itaya, Japan, Japanese Navy, Pearl Harbor, Zeke, ZeroHowever, I found such precious little information on Lieutenant Commander Shigeru Itaya, other than the oft-repeated fact that his Zero was the first plane airborne during the attack on Pearl Harbor, that I reasoned some readers would be interested in my amateur research. I found scant references to him in the books available to me and the dearth of information extended to the internet, where, despite diligent efforts, a search yielded only dribs and drabs of information.

On a hunch that Itaya might be better known in Japan, I searched Japanese sites and stumbled upon Japanese Wikipedia, where I found that Itaya had his own entry. Unfortunately, the entry was skeletal, with not much more information than that available in English. Still, it was more information than I had. Bearing in mind that I know no Japanese and had to resort to imperfect searches on Japanese websites using Google Translate, below is what little information I could gather from various sources. Itaya’s career highlights may prove somewhat tedious so the casual reader may want to skip to the next post, a review of the 1/72 scale models of Itaya’s Zero.

1. Beginnings

Itaya was born July 10, 1909, and graduated from the Naval Academy in 1929. He was a veteran of the China War and by 1937 is listed as a division officer on the Ryujo aircraft carrier. By 1940, he is listed as group leader on the Hiryu aircraft carrier. By April 1941, Lieutenant Commander Itaya had been named group leader on the Akagi, the flagship of the Japanese Imperial Navy’s First Fleet.

2. Pearl Harbor

According to Jim Rearden in Cracking the Zero Mystery, Itaya himself trained the Zero pilots for the Pearl Harbor raid. He was in overall command of the 43 Zero fighters in the first wave from all six carriers, including the nine from the Akagi, Itaya’s carrier. He was the first to take off, guiding the other 42 Zeros to their destination. Once in Hawaii, Itaya and the eight other pilots of the Akagi attacked Hickam Field, Ewa Air Control, and Ford Island, while the Zeros of the five other carriers had different assigned targets. According to Peter Smith in Mitsubishi Zero, Itaya and his two wingmen shot down an unsuspecting B-17 bomber at Hickam Field that had at that precise moment improvidentially flown in from California. The B-17 crew managed to land the crippled bomber and run for cover, though one unfortunate member was killed in the ensuing strafing by the Japanese Zeros.

3. Port Darwin

Two months later, on February 19, 1941, in an aerial surprise attack that has been called Australia’s “Pearl Harbor,” Itaya led the 36 Zero fighters — nine from each of four carriers — in the bombing of Port Darwin, according to Peter Smith in Mitsubishi Zero. Considered the single most destructive raid in Australian history by a foreign power, the raid on Port Darwin was massive, with more bombs dropped than at Pearl Harbor, though loss of life — at 236 — was one tenth that at Pearl Harbor. Incidentally, the four carriers at Port Darwin had all participated at Pearl Harbor and were the same four subsequently sunk at Midway.

4. Ceylon

Itaya appears again on April 5, 1942, during the surprise “Easter Sunday Raid” on Colombo, Ceylon (now Sri Lanka). As at Pearl Harbor and Port Darwin, Itaya led Zero fighters — this time 36 — that escorted bombers from five Japanese carriers whose targets were British warships, harbor installations, and air bases in an attempt to destroy the British Easter Fleet. Although the day before a PBY Catalina pilot spotted the five Japanese carriers and radioed in their position before it was shot down, the Japanese still achieved surprise in yet another Pearl Harbor-style weekend attack. The attack resulted in the sinking of a British carrier and several other warships and cost the lives of 424 British subjects. However, as at Pearl Harbor, most of the British Eastern Fleet was away from the port, thereby reducing potential damage.

5. Midway

Volumes have been written about the Battle of Midway in June 1942 and anyone reading this is likely familiar with the battle. Thus, I will not repeat that information here. Suffice it to say that, according to Peter Smith in Mitsubishi Zero, Itaya once again was in charge of all the Zero fighters at Midway and, in particular, led the attack on the 15 ill-fated TBD Devastators from the USS Hornet, killing 29 men (only Ensign George Gay survived). Once the Akagi was sunk, its pilots ditched their planes near other Japanese warships and Itaya and others pilots were rescued by the escorting ships.

6. Staff Officer

My admittedly faulty understanding of the Google translation of the Japanese Wikipedia indicates that Itaya became chief of staff for 23 Air Corps in October 1942 and chief of staff of 54 Air Corps in July 1944. Despite checking the indices of numerous books, I found no information on Itaya covering the two-year period between those two appointments. However, logic indicates that like many other highly skilled veteran pilots who survived Midway, he would have been used by the Japanese Navy to train the thousands of new pilots required to restore the staggering losses suffered during Midway and elsewhere as the tide turned against Japan. Still, if anyone has more information, please post a comment.

7. Kuril Islands

On July 24, 1944, just after his 35th birthday, while flying on a Mitsubishi G3M aircraft in the Kuril Islands, Itaya’s plane was accidentally shot down by friendly fire. Although his death is listed as an accident on lists of WWII Japanese pilots, it’s unclear to me whether he was shot down by ground anti-aircraft fire or by a Japanese Army plane. Either way, the G3M bomber went down and Itaya was killed in the crash. It is an interesting coincidence and perhaps a fitting end that a man who had dedicated his entire career to serving Admiral Isoroku Yamamoto, the Commander-in-Chief of the Combined Fleet of the Imperial Japanese Navy, who was killed when his G4M aircraft was shot down, would meet his fate the same way.

8. Was Itaya an Ace?

I found a couple of references on the internet stating that Itaya had made ace during the China War but these statements were unsourced. On the other hand, I could not find Itaya on the lists of Japanese aces I consulted, including Osprey’s Imperial Japanese Navy Aces 1937-45 by Henry Sakaida and Stackpole’s Japanese Naval Fighter Aces: 1932-45 by Ikuhiko Hata et al. It is something of a conundrum that a fighter pilot who graduated from the Naval Academy in 1929 and died in 1944 would have failed to shoot down five planes during his 15-year career, particularly since Itaya was presumably a highly skilled pilot, as evidenced by his position and rank. It is even more perplexing when one considers that from 1937 to 1944 he witnessed seven years of continuous combat firsthand. Furthermore, Itaya would have had many opportunities available during the early years of the Sino-Japanese War, when the Zero reigned supreme over the inferior Russian-made aircraft used by the Chinese, and during the Battle of Midway, where 150 American aircraft were shot down. Perhaps more information will surface in the future that will confirm his status one way or the other.

9. Conclusion

To summarize, the highlights of Itaya’s career parallel that of the Akagi. The Akagi’s victories were essentially Itaya’s victories and the Akagi’s bitter loss at Midway effectively ended Itaya’s career as a pilot. While it is ironic that a pilot who survived countless aerial encounters was ultimately shot down by friendly fire, it is hardly surprising that Itaya did not survive the war, for only a handful of the elite Japanese Zero pilots at Pearl Harbor managed to do so. What is surprising is that there is no evidence that Itaya made ace during his 15-year career as a pilot during one of the most tumultuous and target-rich periods in aerial warfare.

Below are two lagniappe group photos from the Hiryu and Akagi aircraft carriers. The photo at left is from Itaya’s time on the Hiryu, scanned from Hata et al’s Japanese Naval Aces and Fighter Units (1989 version translated by Don Gorham). The photo at right is from Itaya’s time on the Akagi, scanned from Hata et al’s Japanese Naval Fighter Aces (2011 version translated by Christopher Shores). The content and photos of the two versions of Hata et al’s book differ somewhat.

itaya-hiryu    itaya-akagi

Again, thank you for your indulgence. I hope you enjoyed the post, or at least found it informative. I will continue to update this post as I come across more information or photos on Itaya. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome, particularly in this case where so little information on Itaya is available. Please stay tuned for reviews of prebuilt 1/72 scale models of Itaya’s Zero in the next three posts.

The Sherman in 1/72: A Firefly Named “Carole” in Normandy, Part 2 – “Brewing Up”

This is Part 2 of A Firefly Named “Carole” in Normandy. For a description of the actual tank and a review of the Dragon model, please refer to the previous post here.

The Crew of the “Carole” in Normandy

I was intrigued by the photo of the four young members of “Carole’s” crew in front of their vehicle “brewing up” at Gosport just before leaving England on their way to Normandy. The human interest value of the photo is immense, as we know the fate of at least two of these young men — Commander Fred Scamp perished soon thereafter, while Gunner Douglas Kay survived into old age. This type of photo where you look into the faces of men who will soon face their fate is always touching to me, whether the soldiers are American, British, Russian, German, Japanese, or any other nationality.

At any rate, I wanted to recreate the aforementioned photo, or something that evinced its feel. However, the fact that the photo was taken while “Carole” still had the wading trunk made it a non-starter as the Dragon model is of “Carole” after the trunk was removed. In addition, recreating anything that even looked like the background in the scene was beyond my meager modeling capabilities. The only avenue available to me was to depict the scene after “Carole” and its crew arrived in Normandy.

The aforementioned photo is on the left in the triptych below. (See previous post for a larger, uncropped view of this photo.) The middle photo shows “Carole” in Normandy. Note the high grass, the stone wall behind the tank, and the destroyed buildings behind that wall. The photo on the right shows a similar scene of a British tank crew with their Sherman. An interesting feature of the photo is that it includes tankers wearing different clothing. Click on the photo to enlarge it.carole-triptych-blue-lineThe Diorama

The diorama below is a composite of those three photos. The modest effort depicts the crew taking a break in front of their tank somewhere in Normandy. Note the tall grass and stone fence present in some photos taken during the Normandy campaign. I’m not unaware that the stone fence is inexplicably intact while the building is in ruins and the tree next to it is completely charred. Still, I concluded that carving rocks out of the wall to simulate damage would not be worthwhile as it could not match the picture in my head anyway.1-008-best-bwBelow is the same photo in color. Ever the philistine, I’m convinced that color photos are infinitely better than black & white photos. To me, continuing to film in B&W in this day and age, as was done in The Good German, which is actually an excellent film, is as silly as would be continuing to film silent movies even though we’ve mastered sound.

Note that the six tankers sport different uniforms, with the 1st, 4th, and 6th (from left) wearing standard British battledress serge while the 2nd and 3rd figures wear denim overalls. The 5th figure is dressed more casually, reflecting the motley nature of clothing in units throughout the war. These Milicast figures are nothing short of cromulent*. Click on the photo to embiggen* it.1-008-bestNote that all the men wear a black beret, the hallmark of a WWII British tanker. According to Military Modelling Vol.30 No.11, the design of the distinctive black beret was inspired by French berets used during WWI. The unstiffened crown allowed it to be easily stowed in the tight spaces within the tank while the dark color helped hide grime and stains inherent in working inside a tank.

This is not an idle observation as knowing that Brit tankers wore a black beret and Brit paras a red one would greatly enhance the casual viewer’s enjoyment of a A Bridge Too Far, as a red beret would immediately signal that the action is taking place at Arnhem. 🙂 By the same token, recognizing the “Screaming Eagles” patch versus the “All American” patch immediately reveals whether the action is taking place at Eindhoven or Nijmegen.3-032Note that the animals move from photo to photo. The tan horse with a white blaze, in particular, had trouble staying on its four legs so every time it tipped over I placed it somewhere else. 🙂 The photo below is my favorite out of the dozens I took of this diorama, though I’m uncertain why.4-030

“Everyone has a backstory and deserves a guess in the absence of facts,” Ara Hagopian.

For the first time in writing these posts I had an urge to create a backstory for the cat I whimsically placed just behind the turret number. Do my fellow German bloggers, who seem to be cat lovers, or any other readers have any ideas? 5-015The cattle and horses are Preiser HO scale prepainted figures, which at first blush appeared to me to be the same size as the horses and cattle in the unpainted Preiser 1/72 scale 72511 Horses, Cows, and Sheep set. 

An indolent man at heart, I opted for the prepainted figures to avoid: 1) clipping the 72511 figures from the sprue; 2) cleaning the flash and seams; 3) gluing the two halves of each figure together; 4) priming them to ensure the paint adheres; 5) painting them; 6) detailing them; and 7) being disappointed with the results. I learned afterwards, upon actually placing the two sets side by side, that the 1/72 scale figures were proportionately larger than the HO scale figures. Alas, Preiser is a German company, after all.6-066Note the tarps and blanket rolls on the rear hull of the tank. These are Value Gear pieces and they are superb. The stone fence is a Pegasus product that surprisingly looked the part with a simple black wash. 7-060Below is a fairly clear shot of the ruined building, which I had trouble bringing into focus at the same time as the tank and crew. Again, a photographer I am not. The realistic building is from the PMA Stalingrad set. PMA diorama pieces are really quite nice, though difficult to find.8-067“Brewing Up”

Much has been written about the British soldier’s expectation of regular tea breaks to the detriment of achieving the objective. Some have offered explanations of this phenomenon cloaked in scholarly terms. Nonsense. The Brits may love their tea, but as their opponents have found out throughout history, they certainly achieve their objectives.british-drinking-teaFor those of us non-British subjects, the 1977 film A Bridge Too Far was in some respects a formative reference on the peculiarly British affinity for drinking tea. The star-studded film has two important tea-related scenes that left an indelible impression on this blogger. 

The first scene, with Sean Connery, perfectly encapsulates how the British perceive drinking tea:

Major General Urquhart:

“Hancock, I’ve got lunatics laughing at me from the woods. My original plan has been scuppered now that the jeeps haven’t arrived. My communications are completely broken down. Do you really believe any of that can be helped by a cup of tea?

Corporal Hancock:

“Couldn’t hurt, sir,” as he hands Urquhart a cup of tea.

YouTube link: https://www.youtube.com/watch?v=LKr9eja-1cw

The second — this time heated — exchange features Robert Redford, and is more a reflection of how Americans perceive the British love affair with tea:

American Officer:

“I don’t understand, why aren’t you moving, what’s the matter with you guys? Those are British troops at Arnhem. They’re hurt, bad. You’re not going to stop, not now.”

British Tank Officer:

“I’m sorry, we have our orders.”

American Officer:

“We busted our asses getting here. Half my men are killed. And you’re just gonna stop . . .  and . . . drink tea? “

YouTube link: https://www.youtube.com/watch?v=i1EsDkm_r3o

At the risk of belaboring the point, I believe ABTF was simply propagating an incorrect — yet widely held — belief among American soldiers that tea time was fairly important to the British. Still, at least in this case, let’s not blame Hollywood as this was a joint British/American production. ABTF was written by Cornelius Ryan, an Irishman; the screenplay was written by William Goldman, an American; and the film was directed by Richard Attenborough, an Englishman.

(Incidentally, what a cast! Laurence Olivier, Sean Connery, Ryan O’Neal, Anthony Hopkins, Robert Redford, Michael Caine, Gene Hackman, Dirk Bogarde, Edward Fox, Elliot Gould, and James Caan, just to name the Allies. Only Is Paris Burning?, Tora, Tora, Tora, and Midway come close. Also, those were real C-47 Skytrains/Dakotas in the film — eleven of them in total, borrowed from various countries, including Denmark, Djibouti, Finland, and Portugal. Sorry, I couldn’t resist. 🙂 )

a-bridge-too-far-2-big

Irrespective of how it came to be, or whether it’s a fair or accurate characterization, it is undeniable that tankers-teaBritish tankers are now firmly entrenched in the modeler’s psyche as soldiers with a strong love affair with tea. Thus, regardless of the scale, they are often depicted “brewing up” with a “cuppa” in hand. The photo triptych at left, showing tanker figures in different scales, makes the point clearly. At left is the Milicast 1/76 figure used in the diorama; at center is a Dartmoor 1/48 figure; and at right is a Dragon 1/6 figure. The first two photos are from their respective manufacturer’s websites; the third I scanned from an article in the French magazine Steel Masters #58.

List of Diorama Pieces

For those interested, below is the source of each piece:

  • Tank: Dragon 60250 Firefly Vc, 13th/18th Royal Hussars, 27th Armoured Brigade, Normandy 1944;
  • Tarp and Blanket rolls on hull: Value Gear Allied Tents, Tarps, and Crates;
  • Crew: Milicast 061 British Squaddies and Milicast 054 British Troops;
  • Animals: Various Preiser HO and 1/72 sets;
  • Trees: Various Woodland Scenics;
  • Building: Precision Model Art PMA P0204 Stalingrad;
  • Stone Fence: Pegasus Hobbies 5202 Stone Walls;
  • Spoked Wheel: Hat 8260 WWI German Field Wagon;
  • Meadow: Woodland Scenics Grass Mat;
  • Tufts of Grass: Noch Scenemaster, Spring Grass Tufts; and
  • Backdrop: Silk poster ordered on Amazon from China.

I hope you enjoyed this simple diorama of “Carole” and its crew. Again, if something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, observations, and backstories for the cat are welcome.

————————————————————————————————————————————–

Once again, I’d like to thank my friend and fellow collector J. Buccellato of NY for his incredible skill and patience in painting the Milicast figures. He’s the sine qua non in creating these dioramas. His “therapy” is my joy. *For those not familiar with the two neologisms in this post, I highly recommend Season 7, Episode 16 of the Simpsons on the episode’s 20th anniversary. 🙂

The Sherman in 1/72: A Firefly Named “Carole” in Normandy, Part 1 – The Tank

Tank enthusiasts frequently admire a tank and blissfully identify its markings as well as its physical features — the version or type of hull, turret, gun, running gear, or tracks. This tendency to focus on the vehicle, rather than what it represents, holds especially true for Sherman tanks, which carry dizzying combinations of  these various elements. We often forget, however, that each of these fighting vehicles was manned by five young men who had names and families and dreams, and many made the ultimate sacrifice inside those very vehicles. “Carole” stands out in that Douglas Kay, its gunner, survived the war and serves as a reminder of the human element we often ignore.

The Actual Tank

“Carole” was a Sherman Mark V Firefly belonging to the 13th/18th Royal Hussars Regiment of the 27th Armoured Brigade of the British Army. In its eight-month operational life, “Carole” participated in the D-Day invasion in Normandy in June 1944 and in Operation Market Garden in Holland in September 1944. It was destroyed in Germany in February 1945.

Below is the best known photo of “Carole” preparing to be loaded onto a Normandy-bound landing craft at the Port of Gosport in Southern England, on June 3, 1944. The photo is from the Imperial War Museum archives (IWM H38995) and is used here under their non-commercial license. Note the deep wading trunk at the rear of the hull, behind the gun, which itself has been traversed to face the rear for embarkation. THE BRITISH ARMY IN THE UNITED KINGDOM 1939-45 (H 38995) A Sherman Firefly and Sherman tanks of 'C' Squadron, 13th/18th Royal Hussars waiting to be loaded aboard landing ships at Gosport, 3 June 1944. The Firefly crew in the left foreground are Trooper Fred Shaw, Trooper Doug Kay, Sergeant Fred Scamp and Trooper Bill Humphries. Their vehicle was named 'Carole'. Copyright: © IWM. Original Source: http://www.iwm.org.uk/collections/item/object/205126259“Carole” and the 13th/18th Royal Hussars took part in the Normandy landings on Sword Beach on June 6, 1944, successfully spearheading the invasion force in support of  the British 3rd Infantry Division. Sword Beach, assigned to the British Army, was the easternmost Allied landing site. All told, almost 30,000 allied troops came ashore at Sword Beach, with losses of 683 men. The IWM photo below shows “Carole” still equipped with its wading trunk.carole-4-2Below is another IWM photo (B5471) of “Carole” in the village of Bréville-les-Monts, on June 13, 1944, a week after D-Day. The Germans had occupied the village in early June and from there had been attacking British positions at Sword Beach. “Carole’s” unit, Squadron C of the 13th/18th Royal Hussars, successfully supported the 6th Airborne Division in securing Bréville, thereby protecting the beachhead. Forgive the graininess of the photo, which has been enlarged from a shot taken at considerable distance. Note that by this time the trunk had been removed.carole-scan-1Once the landings were completed and secured, the British Army disbanded the 27th Armoured Brigade in July 1944, and “Carole” and the 13th/18th Royal Hussars were transferred to the 8th Armoured Brigade. During this time, “Carole” is credited with knocking out a Tiger and a Panther on August 11-12, 1944, towards the end of the Normandy campaign. As part of Operation Market Garden, “Carole” crossed the Nijmegen Bridge, a key Allied objective, on September 21, 1944. The fighting was so brutal at Nijmegen that it came to be known as “Little Omaha” and has been compared to Guam, Tarawa, and Omaha Beach.

“Carole” was destroyed on February 12, 1945, in Goch, Germany, by an 88mm round that entered through the mantle and lodged itself in the radio box at the rear of the turret. The round killed Sgt. Fred Scamp, the commander, and Trooper Wilson, a substitute gunner who was filling in for Douglas Kay, who was on leave that particular day. Kay refers to himself as the “luckiest man” in the world because of this tragic but fortuitous event.

The Model

The Dragon 60250 Sherman Firefly is a special Dragon release issued during the 2006 Dragon Expo in Europe. It is one of the most sought-after Dragon fireflies, and for good reason. A look at the photos below reveal a finely crafted model from Dragon’s heyday, when workmanship was at its apex. The model represents “Carole” after the landing at Normandy, once the wading trunk had been removed. “Carole” was assigned to “C” Squadron, necessitating that its name begin with that letter. Sgt. Fred Scamp, the tank commander, named “Carole” after his daughter, who was born in 1944. In the photo below, note the red circle indicating “C” Squadron, just aft of the name. A triangle would indicate “A” Squadron, while a square would indicate “B” Squadron.1-port-3-047-3Below is a front view photo. Note that “Carole” has the early bolted three-piece transmission cover, as opposed to the cast one-piece cover. Note also that the model does not have the stowage box above the transmission cover visible in the first photo of the actual tank above. This is not a mistake. The stowage bin was temporarily moved from its permanent place at the rear of the hull to the front of the hull to allow the wading trunk to be installed. Once the tank landed and the trunk was removed, the stowage bin was reinstalled in its original place on the rear plate of the hull. Finally, note that while Dragon has often bungled the tracks on its Shermans, “Carole” is equipped with the correct T54E1 steel chevron tracks recognizable in the aforementioned photo.

Dragon faithfully rendered on the transmission cover the colorful and distinctive markings so characteristic of British tanks. Starting from the left, the “33” inside a yellow circle is a bridge classification number, indicating that the Firefly weighed 33 tons, as compared to a standard 30-ton Sherman. The “51” inside the red box identifies the regiment to which “Carole” belonged. The 27th Armoured Brigade had three regiments: the 13th/18th Royal Hussars were assigned “51”; the Staffordshire Yeomanry, “52”; and East Riding Yeomanry, “53.” The yellow seahorse on a blue shield, colloquially known as the “pregnant pilchard,” is the emblem of the 27th Armoured Brigade. The seahorse was a reference to the cavalry roots of its regiments. 2-front-043-3Below is a starboard profile photo of “Carole.” Note the cast surface on the cheek of the turret, which differs from the smooth surface of the metal on the hull — another example of Dragon’s outstanding attention to detail. The British Firefly wielded a 76.2mm gun and the length of the barrel was a whopping 13 ft. 9 in. Incidentally, each troop comprised four tanks — one 17-pounder Firefly and three 75mm Shermans. The other tanks in “Carole’s” 2nd Troop were “Charmer” (68), “Cameo” (69), and “Cavalier” (70).3-starboard-2-037-2Note the “71” on a square black oilcloth on the face of the blanket box in the photo below. The black square was intended to provide more contrast with the red number, making it more visible. As previously mentioned, the model represents “Carole” after it had landed and the wading trunk had been removed with the stowage box moved back to its original place on the rear plate of the hull. Finally, note Dragon’s signature drybrushing that highlights the edges throughout the tank, providing a “worn” look.5-back-039-2The semi-overhead shot below provides a view of the commander’s round hatch as well as the loader’s rectangular hatch on the top of the turret. Note the radio box attached to the back of the turret. In order to fit the huge 76.2mm gun in the 75mm turret, the British removed the radio from the interior and attached it to the rear of the turret. Attached behind the radio box is a blanket box. Note the War Department identification number “T 228789.” Of course, the “T” indicates “tank.” Among others, an “L” before the number would indicate a lorry, an “M” a car, and an “S” a self-propelled gun. 4-port-4-049-3Beyond the Call of Duty

Probably the most outstanding feature of the Dragon piece is the accuracy of the turret. The close-up photo below clearly shows that the turret of the “Carole” did not have a pistol port.carole-scan-biggest-2 Firefly turrets were converted 75mm turrets, which had a pistol port on the rear port side of the turret. In April 1943, the U.S. Ordnance Department determined that it was a ballistic hazard and ordered builders to eliminate it from the turret. The response from the field was so negative, however, that the Ordnance Department reversed the order in July 1943. Still, a number of 75mm turrets without the pistol port were produced during those three months, and “Carole” appears to be one of those. 

The side-by-side photos below from the Sherman Minutia Website show the two different Sherman 75mm turrets as regards the pistol port — the common one with a pistol port and the uncommon one without. 2-pistol-portsDragon brought us two terrific British Fireflies: the Dragon 60250 “Carole” (right) and the 60251 “Velikye Luki” (left) in the side-by-side photo below. Other than the markings and the addition of the blanket box on the “Carole,” the two are nearly identical. Obviously, the most important difference is the absence of the pistol port on the turret of the “Carole” – highlighted in yellow on the “Velikye Luki.” Dragon could have easily taken a short cut and simply used the same common turret on both. Instead Dragon was faithful to both tanks, and produced two different turrets — in my view, a commendable decision.004-2-paint-2In that same vein, note the siren on the front port side fender just above the tracks. If you click on the photo you will find that the siren has a “V” for victory grill used on the actual sirens — a diminutive detail but indicative of Dragon’s erstwhile zeal.

A Little Back Rub

Forgive the lame pun, but “Carole’s” only fault — the “rub” — is that Dragon failed to include markings on the rear plate of the tank hull. There are no clear photos of “Carole” from the rear, though barely visible on one of the photos above is the “51” regiment number on the port side of the rear plate. However, the photo below from British Tanks in Normandy by Ludovic Fortin clearly shows that other tanks of the 13th/18th Hussars — this is “Balaclava” — carried both the “51” regiment number and seahorse markings on the rear plate.balaclava-markings-scan-paintBelow is a corresponding rear view photo of “Carole” sans markings.003-2The Upshot

There is no question that the Dragon 60250 Firefly is a little gem — a rare combination that brings together human interest, historical significance, and accuracy in detail. From the transmission housing to the rear plate and from the steel tracks to the turret hatches, this piece is well crafted. The accuracy of the turret — with its cast surface, radio box, blanket bin, lack of a pistol port, and markings — makes for an outstanding model. The superb finish, light drybrushing, and crisp markings throughout the tank make this an exceptional piece.

The Profile

In 2005, Military Modelling magazine conducted a series of interviews with Douglas Kay, resulting in a terrific, well-illustrated article in its July 2005 issue that featured “Carole” on its cover. The beautiful color profile below comes from that article. It’s a sure bet that Dragon used this profile as its guide. 6-carole-profile-military-modelling-1024x378What little information there is about the actual “Carole” comes from that issue. Should the reader be interested in finding it, below is a photo of the magazine cover. The triptych also includes a photo of 19-year-old Kay in 1944 and Mr. Kay in his 80’s in 2005.

douglas-kay-tryptichThe Crew

Finally, so we can put faces to “Carole,” below is a lagniappe photo of the crew brewing up. From left to right: Fred Shaw (loader/radio operator), Douglas Kay (gunner), Fred Scamp (commander), and Bill Humphries (driver).

 5-crew-439x369

I hope you enjoyed the post. If something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome. Stay tuned for a simple diorama of “Carole” in the next post.

The Filthy Thirteen of the 101st Airborne Division, Part 5: Preboarding Diorama

This is the fifth and final post of the Filthy Thirteen five-part series. For a synopsis of these colorful characters, creating the figures in 1/72 scale, selecting their weapons, and a look at the finished figures, please refer to the previous four posts, The Filthy Thirteen, Part 1, Part 2, Part 3, and Part 4, respectively.

The Group Photo

As previously mentioned, our 1/72 scale Filthy Thirteen are bareheaded — clearly not in combat as they’re not wearing a helmet. Thus, one of the few plausible diorama options was a scene taking place just prior to boarding the aircraft. Before embarking on a mission, it was customary for a stick of paratroopers to pose for a group photo with the pilot and crew of the aircraft. (A paratrooper stick typically numbered 15-18 men.) The reader is directed to the History Channel’s Dangerous Missions: Pathfinders episode, for example, wherein a paratrooper recalls sitting for the group photo. “They must be taking a photo for our obituary,” he quips wryly. The photo below, for example, is of the 506th Parachute Infantry Regiment just before boarding for a mission. pathfinder-photo-506-pirThe Diorama

The diorama below depicting such a photo shoot at Upottery Airfield in East Devon, England, just before the Filthy Thirteen board their aircraft, is loosely based on this concept. A kneeling paratrooper, a sergeant, and a pilot stand directly facing the photographer, with the rest of the stick arranged in a semicircle in front of a Douglas C-47 Skytrain. A brief discussion and additional photos of the Skytrain appear in a separate section below.z-039-2Below is a close-up photo of the scene. The paratroopers have been discussed extensively in previous posts so I will not belabor them further. However, I point the reader’s attention to the pilot, who is also covered in a separate section below.014-2Below is a view from the right side. I was unable to locate a 1/72 scale U.S. photographer so I ended up using a Preiser HO scale figure. Note the three Jeeps, which were ubiquitous at Upottery Airfield.016-2Below is a view from the left side. Note the markings on the front bumper of the Willys Jeep on the right, which clearly identify it as belonging to the 506th Parachute Infantry Regiment. (Click on the photo to zoom in on the bumper.)020-3Below is an overhead shot. Note the drybrushing on the pilot’s leather jacket, which came out better than I expected, once again proving the adage, particularly applicable to me, that “even a stopped clock is right twice a day.” 034-2For those skeptical that paratroopers would actually pose for photos, I direct you to the photo below of Jake McNiece, taken just before the Filthy Thirteen boarded their C-47 on D-Day.posed-photo

The Pilot

Given that group photos often included the aircraft crew, the scene cried out for a pilot. As shown in the composite photo below, there are several U.S. pilot options in 1/72 scale.

us-pilots-graph
From left to right: Airfix 1748; CMK 72039; CMK 72221; Hasegawa 35008; and TQD-AA9.

While I considered the pilots from the Airfix 1748 U.S.A.F. Personnel, CMK 72039 US Army Pilots (resin), CMK 72221 USAAF Pilots (resin), and Hasegawa 35008 WWII Pilots sets, I ultimately opted for the pilot included in the white metal TQD-AA9 US Airborne Infantry & Pilot set, as I found it to have the quintessential WWII U.S. pilot “look.”

The TQD pilot sports the A-2 leather flying jacket so characteristic of WWII U.S. pilots. a-2-flying-leather-jacket-2The backs of these brown leather jackets were often decorated with squadron insignia, victory slogans, or pinup art, as seen in the illustration at left by Francis Chin taken from Osprey Publishing US Army Air Force. The TQD figure also wears the popular officer’s peaked cap that was often worn with the crown stiffener removed, both to get the stylish “crushed” look and, more importantly, to allow the headset to fit over the cap. Note also that these pilots are almost invariably depicted either smoking a cigarette, as in the illustration, or chomping on a cigar, as in the TQD figure. I rejected the Airfix and CMK figures because they appear to be wearing the winter B-3 jacket with fur collar. I note, however, that CMK resin figures are generally some of the most realistic 1/72 scale figures on the market. Similarly, I passed over the Hasegawa figure because it’s wearing the garrison side cap with earflaps, rather than the more distinctive peaked cap.

The Willys Jeep

Numerous sources of information on the jeep are readily available and the reader is directed to them. However, for the sake of completeness, below are several photos of the jeeps used in the diorama. To my knowledge, there are only two 1/72 scale jeeps that specifically represent the 101st Airborne Division. First, below is the Hobby Master HG4203, US Willys Jeep, 101st Airborne Div., 506th A.B. Regiment, Company “C,” Normandy, 6 June 1944 (2010).081-2Made of diecast, the Hobby Master’s heft is pleasing to the hand. Below is a portside view.094-2Below is a front view shot of the Hobby Master model. The markings of the 101st Airborne Division 506th Parachute Infantry Regiment are clearly visible on the bumper.099-2Pictured below is the only other 1/72 scale jeep specifically representing the 101st Infantry Division, the Dragon 60505, 1/4 Ton 4×4 Truck, U.S. Army Western Front 1944, 101st Airborne Division, 401st Glider Infantry Regiment, France 1944 (2011). 082-2Unlike the Hobby Master, the Dragon 60505 is all plastic and, like other Dragon jeep releases, comes bundled in a package of two. Below is a portside view.083-2Finally, below is a side-by-side photo of the Hobby Master and Dragon pieces. As is readily apparent from the photo, the Hobby Master (left) is slightly larger than the Dragon (right). I note that the proportions of the Hobby Master are identical to those of the Cararama and Zylmex 1/72 scale jeeps and it’s probably at scale. In addition, there are reports that the Dragon jeep is underscaled — probably at 1/76 scale. While the Hobby Master model is diecast and the Dragon piece is plastic, a quick glance at the radiator grilles in the photo below immediately attests to Dragon’s redeeming quality — realism.079-3The C-47 Skytrain

The first thing one notices in the diorama is the fabulous Douglass C-47 Skytrain behind the paratroopers. While the versatile “Gooney Bird,” as the Skytrain was known to Air Force personnel, had various military uses, its primary role was as a transport plane, ferrying paratroopers to its targets and becoming the most widely used transport of World War II. Douglas built 10,700 C-47s and more than 1,000 of these participated in the D-Day invasion alone. Below is a portside view of the diecast Corgi  AA38207 used in the diorama.018-2Band of Brothers, the highly acclaimed TV Mini-Series (2001) depicting the travails of the 506th Parachute Infantry Regiment of the 101st Airborne Division, brought international fame to the 506th PIR and spawned a number of products specifically depicting that unit. The Corgi AA38207, for example, represents the transport for Richard “Dick” Winters, the leader of the first platoon of the 2nd Battalion, 506th PIR of the 101st AD. Below is a starboard shot.031-2Below is a shot taken from the front. The 95 ft. 6 in. wingspan of the Douglass C-47 Skytrain was virtually identical to its German counterpart, the Junkers Ju52 “Tante Ju,” which had a wingspan of 95 ft. 11 in. Note the realistic transparent lens of the landing lights on the leading edge of the wings.022-2As can be readily appreciated in the photo below, the Corgi AA38207 is a magnificent piece of diecast. It’s unfortunate that the model disappeared from the shelves long ago. Note the pilot and co-pilot figures through the windows.027-2Below is shot of the portside fuselage. I almost wish Corgi had designed the model with an opening cargo door but such features often come at the expense of accuracy, making the models look toyish. Still, an opening cargo door would provide additional diorama opportunities.025-2The Terrain 

Because of their small size, creating realistic braille scale dioramas is inherently challenging — at least for a novice like me. In addition, the bases of the figures significantly detract from any setting, no matter how realistic it is. Thus, I had two options to try to improve the diorama: Either clip the bases of the figures as I have done for previous posts, or find a way to hide them. I opted for the latter.

I began by cutting out the flat part of styrofoam paper plate. I proceeded to draw the outline of the bases of the figures on the plate and carefully carved them out. When I inserted the figures into the recessed slots in the flat base, I found to my surprise that they fit snugly and were neatly flush with the base. The photo below shows the figures already embedded in the base. (Click on the photo to zoom in on the base.)z-004-2I then enlarged the base with additional styrofoam plates, covered it with hydrocal plaster to create contoured terrain, and painted it with acrylic paints. Finally, I flocked it with Woodland Scenics green and yellow grass to resemble Upottery Airfield in East Devon, England, whence the flights for D-Day originated. The photo below shows the countours of the terrain.001-2The Meltdown

While taking photos of the diorama in my backyard, I realized that the sky backdrop had warped, completely ruining the photos — and an entire morning. 🙁 Following a couple of hours of frustration attempting to salvage the photos by digitally cutting out the background, I decided to photograph the scene again. I was fairly certain that when I glued the silk poster to the cardboard backing I had achieved a good bond and there had been no warping. Still, I carefully unglued the poster and reglued it, using Elmer’s spray adhesive.

Despite diligent efforts and newly acquired photographic lights, indoor illumination continues to confound me, resulting in my strong preference for outdoor photography with natural light. Thus, after ensuring that there was no warping and the glue had set, I again moved the pieces outside and began to photograph. Alas, within ten minutes, the poster began to warp again. I suddenly realized that the 90 degree heat outdoors was melting the glue. As with the warped deck of an aircraft carrier in a previous project, I was once again paying the price of my incompetence and inability to take adequate photos indoors. Nonetheless, the few photos I managed to take before the meltdown were sufficient for this post. The side-by-side photo below is worth a thousand words.contrast-5

List of Diorama Pieces

For those interested, below is the source of each piece:

  • Photographer: Preiser 28069, Photographer (HO Scale);
  • Pilot: TQD Castings, TQD-AA9, US Airborne Infantry & Pilot Boarding Aircraft;
  • Paratroopers: Various sets (see previous four posts);
  • Jeep (far right): Hobby Master HG4203, US Willys Jeep, 101st Airborne Div., 506th A.B. Regiment, Company “C,” Normandy, 6 June 1944 (2010);
  • Other Jeeps: Dragon 60505, 1/4 Ton 4×4 Truck, U.S. Army Western Front 1944, 101st Airborne Div., 401st Glider Infantry Rgt., France 1944 (2011);
  • Aircraft: Corgi AA38207, Douglas C-47 Skytrain, USAAF 439th TCG, 50th TCW, June 5th, Upottery, England (2014);
  • Meadow: Styrofoam plates painted with acrylic colors and flocked with Woodland Scenics grasses;
  • Backdrop: Silk poster ordered on Amazon from China.

Lagniappe

This series of posts began with a wonderful painting of the Filthy Thirteen by Joel Iskowitz. It is only fitting, therefore, that it end with another beautiful painting. The lagniappe painting below, entitled We Were a Band of Brothers, is by John D. Shaw. It is reproduced here for discussion purposes under the fair use exception to the copyright laws. z-john-d-shaw-we-were-a-band-of-brothersI hope you enjoyed this simple diorama and the Filthy Thirteen series of posts. Again, if something looks amiss, please let me know. I would be delighted to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. As always, comments, questions, corrections, and observations are welcome.

The Filthy Thirteen of the 101st Airborne Division, Part 4: The Finished Figures

This is the fourth of a five-part series on the Filthy Thirteen. For a synopsis of these colorful characters, creating the figures in 1/72 scale, and selecting their weapons, please refer to the three previous posts, The Filthy Thirteen, Part 1, Part 2 and Part 3, respectively.

Although I generally paint my own figures, my skills are mediocre at best, and I was too excited about this particular set to ruin it with my efforts. I freely concede: I’m a dilettante — I dabble in everything and master nothing. Thus, I turned to a genuine hobbyist with real expertise for help. The awesome results of his skill, dedication, and patience follow.  

Before we start, let’s put things in perspective. I fully understand that most people reading this post are z 007 - Copy (2)familiar with 1/72 scale and know the height of a typical figure. However, for those casual internet browsers who happen upon this site, the average 1/72 scale figure is approximately 1 inch or 25 mm tall. Borrowing a practice from the terrific WW2 Germans in 1/72 website, the photo at left provides perspective to help us understand the significant painting challenges posed by this scale. I know hobbyists who use a one-bristle paint brush for detail work. In addition, anyone who has painted 1/72 scale figures will understand the severe eye strain and occasional headache that results from concentrating on a figure — there’s a reason 1/72 is known as braille scale. And yet, those of us who engage in this activity know the nirvana with which we’re rewarded. 🙂 Yes, I love doing it; I just stink at it.

The Painted Figures

The following pictures follow the order established in the Figure Chart of the two previous posts. Unless otherwise specified, comments always refer to the photo below the comments.

BELOW: Here are the first four figures. Note the warpaint on their mugs, bearing in mind that the width of their faces is about 2 mm. Note the patches used to reinforce the elbows and knees on the jackets and trousers, a distinct characteristic of paratrooper uniforms. The Revell BAR gunner (second from left) is wearing the BAR belt with six pockets, each for two 20-round magazines, giving him a total of 240 rounds. Note the magazine pouches on the belt of the ESCI figure with the M1A1 Thompson submachine gun (third from left).

023
From left to right: Revell, Revell, ESCI, and ESCI.

BELOW: Note the hand-painted U.S. flag patches on the right shoulder. Astute observers will immediately notice that the flag is seemingly facing in the wrong direction as the applicable U.S. Army regulation requires that the “star field face forward,” like a flag flying in the breeze as it is carried forward. In other words, the regulation requires the flag to be backwards when on the right shoulder.

However, U.S. paratroopers were allowed to use the regular U.S. flag patch, probably because they were dropped behind enemy lines and needed to be easily identified by advancing U.S. forces. (I found at least a dozen photos of WWII U.S. paratroopers wearing the regular U.S. flag patch on their right shoulders before I was convinced.) 025BELOW: Note the famed Screaming Eagle shoulder patches of the 101st Airborne Division on the left shoulder. Only the painter knows how much eye strain these patches are worth. Another U.S. Airborne characteristic is the M3 trench knife and scabbard attached to the lower leg, as can be seen in the picture above on the right leg of the two ESCI figures on the right. A peculiarity of the ESCI set is that 13 of the 14 figures in the set sport the knife in the same fashion — the prone machine gunner being the only exception. The other sets only have two or three figures carrying the trench knife.027BELOW: The ESCI figure on the far right has the 10-inch M1 Bayonet attached to the folding stock M1A1 Carbine. The M1 Bayonet became standard in 1943, replacing the earlier 16-inch bayonet. Note the “U.S.” designation on the covers of the entrenching tool and canteen on the same ESCI figure. 026BELOW: Here are the second four figures. Note that the head on the Caesar figure on the far left is disproportionately large — a melonhead if I ever saw one. Although the Revell figure (second from left) appeared to lack facial detail, paint really brought it out. Note the 10-inch bayonet attached to the M1 Garand rifle on the Caesar figure on the far right. 

7 028
From left to right: Caesar, Revell, ESCI, and Caesar.

BELOW: Note that the first three figures — the three original Pathfinders with Mohawk haircuts — have the M3 trench knife attached to the lower right leg, making them honest paratroopers. Created by three different sculptors, note the difference in the heads. This variety in heads is realistic and the welcome result of mixing figures from different companies. Note the first aid pouch on the right leg of the walking Caesar figure (far right), who also sports one of the Caesar melonheads. These first aid kits typically contained field dressing and morphine.

030BELOW: ESCI’s attention to detail is evident in the inclusion of a helmet attached to the back of its Pathfinder figure (third from left). Neither the Caesar nor the Revell bareheaded Pathfinders with Mohawk haircuts (first and second from left) thought to include a helmet.032BELOW: Note the M1936 Musette Field bag on the back of the Caesar figure on the far right. Though usually associated with paratroopers, this lightweight canvas backpack was also available to officers in the regular infantry.031BELOW: Here are the last four figures. Note the Imex figure (second from left) is tall but slim, lending greater variety to the figures. Note the yellow gloves on the Italeri figure holding the M9 Bazooka (far right), recommended to protect the hands in case of back-flash when the rocket left the muzzle.

033
From left to right: Caesar, Imex, Imex, and Italeri.

BELOW: Note that the Italeri bazooka gunner (far right) has the M3 trench knife on his lower right leg.

034

BELOW: I could not identify the bag on the left hip of the Caesar figure (far left). While it’s probably an M1936 Musette field bag, it’s missing the two straps and buckle to close the flap, as seen on the two Imex figures next to it.

036

BELOW: Of particular interest is the folded M1A1 Carbine on the back of the bazooka gunner (far right). This may be the only folding stock M1A1 Carbine that is actually folded in the various sets. On the same figure, note as well the superb rendition of the “U.S.” designation on his canteen. Note that both Imex figures in the middle have the M1936 Musette field bag. As with the ESCI sculptor who included the distinctive trench knife on virtually all his paratroopers, the Imex sculptor’s idiosyncrasy was to include the characteristic musette field bag on all but two of his 14 paratroopers.

035BELOW: Here are some photos of the TQD figure, completing the Filthy Thirteen. It bears mentioning again that TQD white metal figures are generally excellent, with realistic proportions, fine detail, and historical accuracy. 

Pathfinder (2)
TQD AA5 Pathfinder white metal figure

Comparison Chart

Finally, below is a lagniappe comparison chart that summarizes the project. It shows the original figures with helmets, the set they came from, the figures with the transplanted heads, and the finished figures, as well as the weapon each carries.Filthy Thirteen Final 2

The Upshot

I was pleasantly surprised by the results of this project, an honest and well-intentioned 1/72 scale tribute to the Filthy Thirteen, “the orneriest, meanest group of paratroopers” who ever lived. And it was loads of fun to boot. However, I do have two regrets, as discussed previously: 1) I wish I’d used an Airfix figure to represent all available U.S. paratrooper sets; and 2) I wish I’d used a figure with an M3 “grease gun” to better represent most of the small arms used by U.S. paratroopers.

I hope you enjoyed this Filthy Thirteen series of posts. If something looks amiss, please remember that I’m just an amateur enthusiast (redundancy intended) and let me know. I would be delighted — truly — to correct inaccurate information so that this may be useful for other 1/72 scale collectors and wargamers. Stay tuned next week or so for Part 5: Preboarding Diorama, a simple diorama featuring these characters. As always, comments, questions, corrections, and observations are welcome. 

—————————————————————————————————————————-

I want to thank my friend and fellow collector Joe Buccellato, of NY, whose love of craft, workmanship, and patience far exceed mine — “therapy,” he calls it. He enthusiastically painted these figures and to the extent they succeed the credit is all his. I’m fortunate he’s a Civil War collector for I doubt he’d part with my WWII figures after he paints them. More of his outstanding work will be featured in future posts.

The Filthy Thirteen of the 101st Airborne Division, Part 3: Selecting the Weapons

This is the third of a five-part series on the Filthy Thirteen. For a synopsis of these colorful characters and creating the figures in 1/72 scale, please refer to the two previous posts, The Filthy Thirteen, Part 1 and Part 2.

U.S. Army Airborne Weapons

The nature of U.S. Airborne troops in WWII was such that their weapons had to be specialized, usually to make them lighter or more portable. Because paratroopers were often dropped behind enemy lines where resupply was uncertain, they had to schlep loads of 100 lbs. or more on their backs, making lighter, more portable weapons a must.

As I mentioned in Part 2, one of my goals was for the 1/72 scale unit to reflect as many of the weapons used by U.S. paratroopers as possible. I compiled the weapons plate below from a number of illustrations contained in various Osprey books, including US Army Airborne 1940-1990, US Paratrooper 1941-1945, US Army Airborne and Paratroops; and US Army Paratrooper in the Pacific Theatre 1943-45. The Pathfinder illustration is by renowned military artist Ron Volstad. The plate summarizes the small arms — hand-held small caliber firearms, such as handguns, rifles, manual, semi-automatic, and fully automatic weapons — used by U.S. paratroopers. US Airborne Paratrooper Weapons 13

Figure and Weapons Chart

Below is a chart showing the weapons used by each of the selected figures. A discussion of each weapon follows. Where the options were limited for a particular weapon, I’ve included photos of the various alternatives.Weapons Chart

Weapons in 1/72 Scale

1. M1911A1 Colt .45 Pistol: The venerable seven-round, semi-automatic .45 caliber “Colt 45,” introduced prior to WWI, was issued to officers, non-commissioned officers, and machine gunners and was so effective that it wasn’t replaced until 1986, 75 years and several wars after its debut.

042
Left, Revell; right, Imex.

Every unit has an officer — always with binoculars and a pistol — and the various paratrooper sets offer different alternatives. However, only the Revell and Imex officers have a pistol in hand and the latter is clearly firing his in combat, leaving the Revell figure as the only choice. See photo inset at left. While it is impossible to determine at this scale what pistols the officers are really wielding, we must assume they’re the M1911A1 Colt .45 pistol, common with U.S. Airborne officers. 

 

2. M3 Submachine Gun “Grease Gun”: The .45 caliber M3 Submachine gun was designed to be a simplified, cheaper ($20) replacement for the Thompson submachine gun. Commonly known as

047
From left to right: Caesar, Imex, Italeri, and Revell.

the “grease gun” because of its visual similarity to an actual mechanic’s grease gun, it was unjustly perceived to be less reliable than a Thompson, though its lighter weight (8 lbs.) made it popular among paratroopers who had to schlep loads of 100 lbs. or more on their backs.

For the most part, I succeeded in representing all the standard weapons used by U.S. Airborne troops shown in the Weapons Plate above. However, I failed to use a figure with the M3 “grease gun,” though there were four available. See photo inset above. Note how well-defined the weapon is on the Imex figure (second from left; click on the photo to enlarge). The proportions, detail, and sculpting on the Imex figures are dead-on.

3. M1 Garand Rifle: The semi-automatic, 8-round .30 caliber M1 Garand rifle replaced the 1903 Springfield rifle as the standard issue for U.S. troops in 1938, giving U.S. soldiers a distinct advantage over the slower German K-98 bolt-action rifle, which had become standard Wehrmacht issue in 1935. General Patton considered it “the greatest battle implement ever devised” and many soldiers preferred the M1 Garand’s greater range and stopping power over the M1 Carbine that was supposed to replace it. By the end of the war, over five million M1 Garands had been produced.

The various U.S. paratrooper sets included many figures with the M1 Garand rifle, reflecting the fact that it was the most common weapon used by U.S. Airborne troops. Thus, there were a number of choices and four of the selected 13 figures are carrying one, including one with the 10-inch M1 Bayonet attached. (See the Figure and Weapons Chart above.) 

4. M1 Carbine w/ Wooden Stock: The semi-automatic, 30-round, .30 caliber M1 Carbine, which replaced the M1 Garand as the standard issue rifle in 1942, was intended to be smaller and lighter than the M1 Garand. At 35.5 in. and 5.5 lbs, it was, in fact, eight inches shorter and weighed four pounds less than the M1 Garand, making it well suited for paratroopers. With more than six million wood-stocked M1 Carbines produced, it was much more widely used by U.S. forces than its cousin, the folding stock M1A1 Carbine, of which only 150,000 were made. However, designed specifically for U.S. paratroopers, the M1A1 Carbine was more common among this group.

As with the M1 Garand rifle, the various U.S. Airborne sets offered a fair selection of figures equipped with the M1 Carbine. As noted, however, the folding stock M1A1 Carbine was more widely used by U.S. paratroopers so I selected only one figure carrying the M1 Carbine, the Revell figure (sixth from left), as can be seen on the Figure and Weapons Chart above.

5. M1A1 Carbine w/ Folding Stock: Identical to the M1 Carbine except for the folding metal stock, the M1A1 Carbine was 25 inches long when folded, fully 10 inches shorter than the M1 Carbine, making it an excellent weapon for the highly mobile paratroopers.

Given that the M1A1 Carbine was specifically designed for U.S. paratroopers, it is no surprise that at least 10 figures in the various U.S. paratrooper sets are equipped with it. The ESCI set alone includes five figures wielding this weapon. There are three figures with the M1A1 Carbine in the selected 13 — the ESCI (fourth from left) and Caesar (ninth from left) figures shown on the Figure and Weapons Chart above plus the Italeri figure (far right) with the M9 Bazooka, who carries the M1A1 Carbine on his back. 

6. M1A1 Thompson Submachine Gun: One of the most recognized weapons in history, the M1A1 Thompson submachine gun was a favorite among the troops. Though generally only issued to squad leaders and officers in the regular army, it was widely used among paratroopers. Accurate up to 50 yards, it could fire its large .45 caliber rounds at a rate of 650 per minute, giving it devastating “sweeping” power within that distance. Though heavier than the M3 “grease gun,” the M1 Thompson submachine gun was more widely used.

The various figure sets provided a fair selection of figures wielding the M1A1 Thompson submachine guns, reflecting its wide use among paratroopers.  As shown in the Figure and Weapons Chart above, I selected three — the ESCI figure (third from left), the kneeling Caesar figure (fifth from left), and the TQD Pathfinder figure, a picture of which appears in the previous post.

7. M1918A2 Browning Automatic Rifle (BAR): The fully automatic .30 caliber M1918A2 BAR, which replaced the M1918 used in WWI, was designed to be fired from the hip as an automatic rifle while moving forward in support of riflemen or from a stationary position as a light machine gun.

13 002
Left, Imex; right, Revell.

However, its paltry 20-round magazines greatly limited its effectiveness as a machine gun. While used by U.S. paratroopers, the BAR’s 20-lb weight and need to be reassembled after a jump made it an inconvenient — and therefore uncommon — weapon for Airborne troops. To reduce the BAR’s weight, experienced paratroopers often ditched the bipod, buttplate, and carrying handle, lowering the weight to 15 lbs.

There are only two BAR gunners in the 69 paratrooper poses available — one in the Imex set and one in the Revell set, as seen in the photo inset above. Thus, the Revell figure (on the right) was an easy choice since the Imex figure is prone firing the weapon, clearly in combat. The Revell gunner, who has not removed the bipod or carrying handle from his BAR, is presumably a novice. 🙂 

8. M9 Bazooka: The M9 Bazooka was a portable recoil-less, anti-tank rocket launcher that replaced the earlier M1 Bazooka in 1943. At 54 inches, the M1 Bazooka was unwieldy during jumps so the Airborne command specifically requested the M9 Bazooka, which could be broken down into two parts to make it more portable. By happy coincidence, the modification allowed engineers to make it longer, increasing range and accuracy.

14 001
From left to right: Caesar, Imex, and Italeri.

Considered the perfect infantryman’s anti-tank weapon, it could immobilize a tank with a solid, accurate hit. According to the conventional wisdom, the much-feared German 88mm Panzershreck was copied from a captured American bazooka.

The M9 Bazooka was common with U.S. Airborne troops so the set would have been incomplete without a figure carrying one. There were three potential figures with a bazooka, as can be seen in the photo inset above. However, two of them are actually firing the weapon so the Italeri figure was the only non-combat choice. 

A passing glance at the Figure and Weapons Chart above quickly reveals that the Italeri figure (far right) is somewhat bulkier than the other 12, which gave me pause. In the end, I used it anyway. First, I rationalized that human height and girth varies significantly. It turned out that the figure is 26.4mm tall, which scales out to only 6’2”, totally within the acceptable range. He is crouching a bit, which means he’s actually taller. Secondly, the figure — huge as it is — represents the gentle but slow-witted giant often seen in Hollywood movies, including the one in the aforementioned Dirty Dozen. (To my mind, the all-time greatest Hollywood brute is Andre the Giant as the unforgettable Fezzik in The Princess Bride.) And finally, it makes sense that the biggest man in the unit would carry the M9 Bazooka, the heaviest weapon in the paratrooper arsenal, weighing 16 lbs — one pound more than the stripped down 15-lb BAR. 

Browning M1919A4 Light Machine Gun

I intentionally did not include the Browning M1919A4 light machine gun in the Weapons Plate or in the discussion, as there were no figures carrying it in non-combat. However, four of the six sets include such a weapon and, for the sake of completeness, I’ve included a lagniappe photo of those four below. Referring strictly to the weapon and not the paratrooper, the ESCI machine gun (far left) has the most detail and best proportions, with the Revell and Italeri weapons closely behind. The Caesar machine gun (far right) is underscaled and has very little detail, though the paratrooper figure itself is excellent.

BMG 004
From left to right: ESCI, Revell, Italeri, and Caesar.

This concludes our lightning-fast survey of U.S. Army Airborne small arms. I hope you found the post informative. Stay tuned tomorrow for Part 4: The Finished Figures, with lots of photos of the painted figures. As always, comments, questions, corrections, and observations are welcome.